Rigging Your Bait - Successful Fishing Methods - Rivers Inlet, BC - Legacy Lodge -

Rigging Your Bait

Easy steps for rigging your bait

Cleaning the Herring

All of our herring are expertly cut and brined for our guests. Before handling the bait make sure your hands are wet, this will help to keep the scales in place. When handling the bait, be gentle, insuring you keep its shape and pristine shine. A roughly handled bait will not spin well and is less attractive to the salmon!

Remove the entrails by inserting the bait knife into the cavity; spin the knife several times inside the cavity and remove the entrails. Be sure to get everything out as you do not want entrails trailing the bait.

Watch the Video



Venting the Herring

Venting the bait allows water to pass through the bait and reduces water drag and resistance, creating a tighter spin while helping to prevent the belly from ripping out of the bait. Simply cut the anal vent larger from the inside to the outside of the cavity by gently pushing the bait knife’s tip out through the anal vent, creating about a ½” incision.



Rigging your Bait

Every guide seems to have their preferred method of rigging herring. There is no single best method; but all of the methods strive to achieve the same result – a tight roll or spin on the herring, under varying speeds, with optimum hook coverage on the bait. Your method should be something you can repeat consistently and quickly. The following is a method I have used for years; it’s both easy and provides the desired roll on the bait while achieving consistent hook-ups.

Watch the Video




Hook Placement

The angle of the cut, plus the positioning of the tow hook controls the tightness and speed of the roll. The positions between 11 and 1 O’clock, closest to the spine, will give you the tightest, fastest rolls.

If you look at your herring straight on, with the body cavity opening facing you, you’ll see the herring’s spine at the top of the cavity (12 o’clock position). when rigging your herring, make sure your tow hook always goes through the spine. This is the toughest part of the bait and will help keep your hook from tearing out of your bait.

The closer your hook is to the 12 o’clock position the tighter your herring will roll. Placing your hook towards the 3 o’clock position will create slower, wider rolls. You can go from the left or the right side, but go through the spine.

Start your hook inside the body cavity, going up through the spine at the 11:45 position and out at the 12:15 position. The point of the hook should poke through the top of the herring and be pointing forward. The hook should be 1/4″ to 3/8″ deep into the herring. If the tow hook is placed too deeply into the herring it will create a hinge point, and your bait will not spin properly.



Trailing Hook

Take the trailing hook (bottom hook) and carefully reach into the cavity and work the hook out the side of the bait on the lateral line – pull the hook all the way through the bait while being careful not to tear the bait. This hides the line inside the herring’s body cavity.

With the herring in your hand, tail facing towards you, insert the trailing hook into the lateral line between the dorsal fin and the tail and roll the hook towards you carefully turn the eye of the hook over and pull the eye of the hook into the herring being careful not to tear the herring or remove scales. Once the eye of the hook is in the herring, gently push the eye into the meat of the herring so only the curve of the hook is visible.


Check your Roll

With your herring rigged and ready to fish, put the boat into gear and obtain your approximate mooching speed. Put your bait in the water (always check to insure your gear in not fowled) and check to insure you have a tight roll on the bait. If the bait looks good, put out the desired amount of pulls and start fishing. If the bait does not have a tight roll, try giving the bait a quick jerk through the water. This sets the tow hook and often corrects the problem.

Watch the Video



Tuning the Bait

A bait that is not spinning on the first attempt can be tuned to spin properly. To tune the bait simply change the clock position of the front tow hook, or switch from the long side to the short side of the bait-fish. Often this slight change will have the bait spinning tightly. Remember not to get too deep into the herring with the tow hook, as this will prevent the herring from spinning properly.


Helpful Downloads: